ADI’s ADP5003ACPZ-R7 integrates a high voltage buck regulator and an ultra-low noise low dropout (LDO) regulator. The buck regulator is optimized to operate at high output currents up to 3 A. The LDO is capable of a maximum output current of 3 A and operates efficiently with low headroom voltage while maintaining high power supply rejection. The ADP5003ACPZ-R7 can operate in one of two modes: adaptive mode or independent mode. Adaptive mode allows the LDO to operate with a set headroom by adjusting the buck output voltage internally. Alternatively, the ADP5003ACPZ-R7 can operate in independent mode, where both regulators operate separately from each other, and where the output voltages are programmed using resistor dividers. The LDO regulator output can be accurately controlled at the point of load (POL) using remote sensing that compensates for the printed circuit board (PCB) trace impedance while delivering high output currents. Each regulator is activated via a dedicated precision enable input. The buck switching frequency can be synchronized to an external signal, or programmed with an external resistor. Safety features in the ADP5003ACPZ-R7 include thermal shutdown (TSD) and input undervoltage lockout (UVLO). This PMU is rated for a -40°C to +125°C operating junction temperature range and comes in a small, 5 mm x 5 mm, 32-lead LFCSP package. The ADP5003ACPZ-R7 is an ideal solution to provide highly efficient and quiet regulated supplies for low noise power applications found in analog-to-digital converters (ADCs), RF transceivers, and clocking ICs.<strong>Features:</strong> High-efficiency buck for first stage conversion, High PSRR, low noise LDO regulator to remove switching ripple, 3 A, low noise, buck regulator Wide input voltage range: 4.2 V to 15 V, Programmable output voltage range: 0.6 V to 5.0 V, 0.3 MHz to 2.5 MHz internal oscillator, 0.3 MHz to 2.5 MHz SYNC frequency range, Temperature operating range:-40°C to +125°C, Adaptive LDO regulator headroom control option for optimal efficiency and PSRR across the full load range, 3 A, low noise, NFET LDO regulator (active filter) Wide input voltage range: 0.65 V to 5 V, Programmable output voltage range: 0.6 V to 3.3 V, Differential point of load remote sensing, Package/case: 32-LFCSP, Low noise power for high-speed ADC and digital-to-analog converter (DAC) designs, Powering RF agile transceivers and clocking ICs
Feature
- Low noise, dc power supply system
- High efficiency buck for first stage conversion
- High PSRR, low noise LDO regulator to remove switching ripple
- Adaptive LDO regulator headroom control option for optimal efficiency and PSRR across full load range
- 3 A, low noise, buck regulator
- Wide input voltage range: 4.2 V to 15 V
- Programmable output voltage range: 0.6 V to 5.0 V
- 0.3 MHz to 2.5 MHz internal oscillator
- 0.3 MHz to 2.5 MHz SYNC frequency range
- 3 A, low noise, NFET LDO regulator (active filter)
- Wide input voltage range: 0.65 V to 5 V
- Programmable output voltage range: 0.6 V to 3.3 V
- Differential point of load remote sensing
- 3 μV rms output noise (independent of output voltage)
- PSRR > 50 dB (to 100 kHz) with 400 mV headroom at 3 A
- Ultrafast transient response
- Power-good output
- Precision enable inputs for both the buck regulator and LDO
- −40°C to +125°C operating junction temperature range
- 32-lead, 5 mm × 5 mm, LFCSP
Applications
- Low noise power for high speed analog-to-digital converter (ADC) and digital-to-analog converter (DAC) designs
- Powering RF transceivers and clocking ICs
(Picture: Pinout)