PTN5100BSMP is a single port USB Type-C Power Delivery (PD) PHY and Protocol IC that providesType-C Configuration channel interface and USB PD Physical and Protocol layer functionsto a System PD Port Policy Controller (Policy Engine and Device Policy Manager,Alternate mode controller). It complies with USB PD and Type-C specifications and deltaupdates of PD spec. This IC is targeted for a wide range of platforms (Standard NotebookPCs, Desktop PCs, Chromebooks, Tablets, Convertibles, Smart phones) and PC Accessories(e.g. Docks, Monitors, Cable adapters etc.) applications. PTN5100BSMP is architected todeliver robust performance, compliant behavior, configurability and systemimplementation flexibility that are essential to tide over interoperability andcompliance hurdles in the platform applications.
PTN5100BSMP can support system realization of the following PD roles: (i) Provider (P) only,(ii) Provider/Consumer (P/C) (iii) Consumer only (C) (iv) Consumer/Provider (C/P).Further, it can be register programmed to operate in Type-C specific Upstream FacingPort (UFP), Downstream Facing Port (DFP) or Dual Role Port (DRP) role.
PTN5100BSMP implements VCONN low RON switch with register programmable Forward Currentprotection feature. The VCON switch also provides Reverse current protection feature todetect reverse current flow into the system whenever (inductive or) charged cable isunplugged from the connector.
PTN5100BSMP operates from platform power supply VDD, or it can also be powered from USB powerVBUS directly, which is especially required for operation under Dead Battery (DB)condition and certain platform use cases. The host interface operates on VIO supply tofacilitate interfacing to systems that use IO supply rail different from VDD supplyrail.
It provides SPI/I2C interface for system host control/status update. The interface choiceis pre- configured in NXP factory.
PTN5100BSMP is available in a small footprint package option: HVQFN20 4 mm x 4 mm, 0.5 mmpitch.
Feature
- Supports Type-C role configurability
- Type-C role (DFP, UFP, DRP) is Non-Volatile Memory (NVM) and registerprogrammable based on OEM platform requirements
- Implements UFP role pull down behavior to handle dead batterycondition on battery powered platforms
- Supports register programmable and variable ‘Rp’ indication (forDRP/DFP usage and accessory detection)
- Implements 'Rd' indication on CC pin (for Device sideimplementation)
- CC detection/indication scheme based on Type-C role
- Indication of orientation detection via CC_ORIENT pin and statusregister(s)
- Debug and Audio Accessory detection and indication in statusregister(s)
- Cooperatively works under the control of Policy controller MCU for power deliverynegotiation and contract(s), Alternate mode and VDM exchanges
- Implements BMC (de)coding, 4B5B symbol (de)coding, CRCgeneration/checking, PD packet assembling/disassembling includingPreamble, SOP, EOP, Good CRC response, Retries, Hard and Cableresets
- PD PHY and Protocol layer interface control and status update handledvia SPI/I²C interface
- SOP Configurability
- Register programmable to generate and receive SOP, SOP', SOP'-debug,SOP", SOP"-debug'' in DFP/DRP (host use case)
- Register programmable to receive and respond on SOP, SOP'-debug andSOP"-debug commands
- Supports low RON VCONN switch with enable/disable (Hi-Z) support
- Capable of maximum current delivery of 1 A over 2.7 V to -5.5 V
- Supports register programmable Forward current protection control
- Supports register programmable reverse current protection
- Back current protection on all pins when PTN5100 is unpowered
- CC1 and CC2 pins are 5.5 V tolerant
- VBUS pin and VBUS power path MOSFET enable pins are 28 V tolerant
- Delivers (active LOW enable) gate control signals for PMOS Power MOSFETs on VBUSsource and sink power paths
- Provides dedicated IO pin (CC_ORIENT) for indicating Cable/plug orientation andIO pin (DBGACC_FOUND) for indicating Debug accessory detection
- Delivers up to 30 mA (max) for powering Policy controller MCU
- Supports SPI slave interface (SPI modes 0 and 3 supported) up to 30 MHz
- Supports I²C slave interface standard mode (100 kHz), Fast mode (400kHz) and Fast mode plus (1 MHz)
- I²C Device slave address programmable up to 3 values
- Supports 3.3 V or 1.8 V capable I²C-bus or SPI interface
- Supports register access - device configuration, control andstatus/interrupt interfacing through Slave I²C-businterface
- Power supplies - VDD (3.3 V ±10 %) or VBUS
- Tolerant up to 28 V on VBUS and operational up to maximum of 25 V onVBUS
- Operating temperature -20 °C to 85 °C
- ESD 8 kV HBM, 1 kV CDM
- Package: HVQFN20 4 mm x 4 mm, 0.5 mm pitch
- PC platforms: Notebook PCs, Desktop PCs, Ultrabooks, Chromebooks
- Tablets, 2:1 Convertibles, Smartphones and Portable devices
- PC accessories/peripherals: Docking, Mobile Monitors, Multi-Function Monitors,Portable/External hard drives, Cable adaptors, Dongles and accessories, etc.
